Publisher’s note

Código QR

Publisher’s note

Guardado en:

Detalles Bibliográficos
Formato:	article
Lenguaje:	EN
Publicado:	Taylor & Francis Group 2017
Materias:	Polymers and polymer manufacture TP1080-1185 Automation T59.5
Acceso en línea:	https://doaj.org/article/193b1a62d01f4e0a86253138bccc6736
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Correction
Publicado: (2018)

Use of experimental design to obtain polymeric microfibers with carbon nanotubes
por: Andressa Giombelli Rosenberger, et al.
Publicado: (2020)

A controlled recipient evacuation process to form composite profiles from flat multi-angle prepreg stacks – infrastructure and C-profile verification
por: E. Kappel, et al.
Publicado: (2019)

The advanced ply placement process – an innovative direct 3D placement technology for plies and tapes
por: Marko Szcesny, et al.
Publicado: (2017)

Towards automation of wind energy rotor blade production: a review of challenges and application examples
por: Jan-Hendrik Ohlendorf, et al.
Publicado: (2020)

Quantifying inter- and intra-ply shear in the deformation of uncured composite laminates
por: S. Erland, et al.
Publicado: (2021)

Compression molding of reused in-process waste – effects of material and process factors
por: M.-S. Wu, et al.
Publicado: (2018)

Ply-by-ply inline thermography inspection for thermoplastic automated tape layup
por: Neha Yadav, et al.
Publicado: (2021)

The manufacture of honeycomb cores using Fused Deposition Modeling
por: David Pollard, et al.
Publicado: (2017)

The use of discontinuous PEEK/carbon fiber thermoplastic moulding compounds for thick-section componentry
por: Samuel Erland, et al.
Publicado: (2019)

Increasing the performance of continuous compression moulding by local pressure adaption
por: Florian Piott, et al.
Publicado: (2021)

Influence of manufacturing-induced defects on the fatigue performances of autoclave moulded laminates
por: L. Maragoni, et al.
Publicado: (2021)

Heating rate effects on thermal analysis measurement of Tg in composite materials
por: Ana X. H. Yong, et al.
Publicado: (2017)

Generation of feasible gripper trajectories in automated composite draping by means of optimization
por: Christian Krogh, et al.
Publicado: (2019)

Permeability of co-cured honeycomb sandwich skins: effect of gas transport during processing
por: Trisha Palit, et al.
Publicado: (2020)

Effective cure cycle development via flow optimization and advanced cure environments
por: D. Kim, et al.
Publicado: (2020)

The effects of conductive nano fillers alignment on the dielectric properties of copolymer matrix
por: Md Habibur Rahaman, et al.
Publicado: (2019)

A reference specimen for compaction tests of fiber reinforcements
por: David May, et al.
Publicado: (2019)

Dry fiber placement of carbon/steel fiber hybrid preforms for multifunctional composites
por: Florian Kühn, et al.
Publicado: (2019)

Viscoelastic model with complex rheological behavior (VisCoR): incremental formulation
por: Sibin Saseendran, et al.
Publicado: (2020)

In situ resin age assessment using dielectric analysis and resin cure map for efficient vacuum infusion
por: Jung Hwan Shin, et al.
Publicado: (2020)

Metrological determination of inhomogeneous hydrodynamic compaction during unsaturated out-of-plane permeability measurement of technical textiles
por: B. Willenbacher, et al.
Publicado: (2019)

Heat transfer analysis of automated fiber placement of thermoplastic composites using a hot gas torch
por: Omid Aghababaei Tafreshi, et al.
Publicado: (2019)

Cure-state dependent viscoelastic Poisson’s ratio of LY5052 epoxy resin
por: Sibin Saseendran, et al.
Publicado: (2017)

Study and characterization of LDPE/Polyolefin elastomer and LDPE/EPDM blend: effect of chlorinated water on blend performance
por: Nikesh B. Samarth, et al.
Publicado: (2017)

Experimental and numerical investigations of pressure-controlled resin transfer molding (PC-RTM)
por: Julian Seuffert, et al.
Publicado: (2020)

Efficient cocured scarf repair of composite structures through rheology modeling
por: David B. Bender, et al.
Publicado: (2021)

Design and application of discontinuous resin distribution patterns for semi-pregs
por: Sarah G. K. Schechter, et al.
Publicado: (2020)

Factors affecting the properties of composites made by 4D printing (moldless composites manufacturing)
por: Suong Van Hoa
Publicado: (2017)

In-situ simultaneous measurement of strain and temperature in automated fiber placement (AFP) using optical fiber Bragg grating (FBG) sensors
por: Ebrahim Oromiehie, et al.
Publicado: (2017)

Uncertainty propagation and sensitivity analysis in composite manufacturing cost estimation: ALPHA-framework and cost tool development
por: Christian Hueber, et al.
Publicado: (2019)

A review of composite product data interoperability and product life-cycle management challenges in the composites industry
por: Alison J. McMillan, et al.
Publicado: (2017)

Effects of debulk temperature on air evacuation during vacuum bag-only prepreg processing
por: Wei Hu, et al.
Publicado: (2020)

Optimization of the laser-assisted tape winding process using an inverse kinematic-optical-thermal model
por: S. M. Amin Hosseini, et al.
Publicado: (2020)

Development and application of a quality control and property assurance methodology for reclaimed carbon fibers based on the HiPerDiF (High Performance Discontinuous Fibre) method and interlaminated hybrid specimens
por: M. L. Longana, et al.
Publicado: (2018)

Resource-friendly carbon fiber composites: combining production waste with virgin feedstock
por: James Kratz, et al.
Publicado: (2017)

Use of recycled carbon staple fibers in an advanced thermoforming process and analysis of its crash performance
por: Florian Mischo, et al.
Publicado: (2020)

Optical thermal model for LED heating in thermoset-automated fiber placement
por: Tilman Orth, et al.
Publicado: (2018)

Effect of the water absorptive capacity of reinforcing fibers on the process ability, morphology, and performance characteristics of composites produced from polyfurfuryl alcohol
por: Katharina Resch-Fauster, et al.
Publicado: (2018)

Real-time quantification of network growth of epoxy/diamine thermosets as a function of cure protocol
por: Andrew P. Janisse, et al.
Publicado: (2019)