Publisher’s note

QR Code

Publisher’s note

Enregistré dans:

Détails bibliographiques
Format:	article
Langue:	EN
Publié:	Taylor & Francis Group 2017
Sujets:	Polymers and polymer manufacture TP1080-1185 Automation T59.5
Accès en ligne:	https://doaj.org/article/193b1a62d01f4e0a86253138bccc6736
Tags:	Ajouter un tag Pas de tags, Soyez le premier à ajouter un tag!

Documents similaires

Correction
Publié: (2018)

Use of experimental design to obtain polymeric microfibers with carbon nanotubes
par: Andressa Giombelli Rosenberger, et autres
Publié: (2020)

A controlled recipient evacuation process to form composite profiles from flat multi-angle prepreg stacks – infrastructure and C-profile verification
par: E. Kappel, et autres
Publié: (2019)

The advanced ply placement process – an innovative direct 3D placement technology for plies and tapes
par: Marko Szcesny, et autres
Publié: (2017)

Towards automation of wind energy rotor blade production: a review of challenges and application examples
par: Jan-Hendrik Ohlendorf, et autres
Publié: (2020)

Quantifying inter- and intra-ply shear in the deformation of uncured composite laminates
par: S. Erland, et autres
Publié: (2021)

Compression molding of reused in-process waste – effects of material and process factors
par: M.-S. Wu, et autres
Publié: (2018)

Ply-by-ply inline thermography inspection for thermoplastic automated tape layup
par: Neha Yadav, et autres
Publié: (2021)

The manufacture of honeycomb cores using Fused Deposition Modeling
par: David Pollard, et autres
Publié: (2017)

The use of discontinuous PEEK/carbon fiber thermoplastic moulding compounds for thick-section componentry
par: Samuel Erland, et autres
Publié: (2019)

Increasing the performance of continuous compression moulding by local pressure adaption
par: Florian Piott, et autres
Publié: (2021)

Influence of manufacturing-induced defects on the fatigue performances of autoclave moulded laminates
par: L. Maragoni, et autres
Publié: (2021)

Heating rate effects on thermal analysis measurement of Tg in composite materials
par: Ana X. H. Yong, et autres
Publié: (2017)

Generation of feasible gripper trajectories in automated composite draping by means of optimization
par: Christian Krogh, et autres
Publié: (2019)

Permeability of co-cured honeycomb sandwich skins: effect of gas transport during processing
par: Trisha Palit, et autres
Publié: (2020)

Effective cure cycle development via flow optimization and advanced cure environments
par: D. Kim, et autres
Publié: (2020)

The effects of conductive nano fillers alignment on the dielectric properties of copolymer matrix
par: Md Habibur Rahaman, et autres
Publié: (2019)

A reference specimen for compaction tests of fiber reinforcements
par: David May, et autres
Publié: (2019)

Dry fiber placement of carbon/steel fiber hybrid preforms for multifunctional composites
par: Florian Kühn, et autres
Publié: (2019)

Viscoelastic model with complex rheological behavior (VisCoR): incremental formulation
par: Sibin Saseendran, et autres
Publié: (2020)

In situ resin age assessment using dielectric analysis and resin cure map for efficient vacuum infusion
par: Jung Hwan Shin, et autres
Publié: (2020)

Metrological determination of inhomogeneous hydrodynamic compaction during unsaturated out-of-plane permeability measurement of technical textiles
par: B. Willenbacher, et autres
Publié: (2019)

Heat transfer analysis of automated fiber placement of thermoplastic composites using a hot gas torch
par: Omid Aghababaei Tafreshi, et autres
Publié: (2019)

Cure-state dependent viscoelastic Poisson’s ratio of LY5052 epoxy resin
par: Sibin Saseendran, et autres
Publié: (2017)

Study and characterization of LDPE/Polyolefin elastomer and LDPE/EPDM blend: effect of chlorinated water on blend performance
par: Nikesh B. Samarth, et autres
Publié: (2017)

Experimental and numerical investigations of pressure-controlled resin transfer molding (PC-RTM)
par: Julian Seuffert, et autres
Publié: (2020)

Efficient cocured scarf repair of composite structures through rheology modeling
par: David B. Bender, et autres
Publié: (2021)

Design and application of discontinuous resin distribution patterns for semi-pregs
par: Sarah G. K. Schechter, et autres
Publié: (2020)

Factors affecting the properties of composites made by 4D printing (moldless composites manufacturing)
par: Suong Van Hoa
Publié: (2017)

In-situ simultaneous measurement of strain and temperature in automated fiber placement (AFP) using optical fiber Bragg grating (FBG) sensors
par: Ebrahim Oromiehie, et autres
Publié: (2017)

Uncertainty propagation and sensitivity analysis in composite manufacturing cost estimation: ALPHA-framework and cost tool development
par: Christian Hueber, et autres
Publié: (2019)

A review of composite product data interoperability and product life-cycle management challenges in the composites industry
par: Alison J. McMillan, et autres
Publié: (2017)

Effects of debulk temperature on air evacuation during vacuum bag-only prepreg processing
par: Wei Hu, et autres
Publié: (2020)

Optimization of the laser-assisted tape winding process using an inverse kinematic-optical-thermal model
par: S. M. Amin Hosseini, et autres
Publié: (2020)

Development and application of a quality control and property assurance methodology for reclaimed carbon fibers based on the HiPerDiF (High Performance Discontinuous Fibre) method and interlaminated hybrid specimens
par: M. L. Longana, et autres
Publié: (2018)

Resource-friendly carbon fiber composites: combining production waste with virgin feedstock
par: James Kratz, et autres
Publié: (2017)

Use of recycled carbon staple fibers in an advanced thermoforming process and analysis of its crash performance
par: Florian Mischo, et autres
Publié: (2020)

Optical thermal model for LED heating in thermoset-automated fiber placement
par: Tilman Orth, et autres
Publié: (2018)

Effect of the water absorptive capacity of reinforcing fibers on the process ability, morphology, and performance characteristics of composites produced from polyfurfuryl alcohol
par: Katharina Resch-Fauster, et autres
Publié: (2018)

Real-time quantification of network growth of epoxy/diamine thermosets as a function of cure protocol
par: Andrew P. Janisse, et autres
Publié: (2019)