Investigation on production of particleboard from Date palm residues

The influence of production variable such as residues moisture content at time of chipping or flaking, hardner and press time on properties of particleboard from date palm residues is investigated. Each variable was investigated at three different levels and a total of 24 combinations of variables w...

Descripción completa

Guardado en:

Detalles Bibliográficos
Autores principales:	Ahmad Jahan latibari, Abdolrahman Hosseinzadeh, Amir Nourbakhsh, Abolfazl Kargarfard, Fardad Golbabaei
Formato:	article
Lenguaje:	FA
Publicado:	Regional Information Center for Science and Technology (RICeST) 1996
Materias:	MOR MOE Date palm Forestry SD1-669.5
Acceso en línea:	https://doaj.org/article/1ccf98b0290c42529c6e03883faf0721
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

id	oai:doaj.org-article:1ccf98b0290c42529c6e03883faf0721
record_format	dspace
spelling	oai:doaj.org-article:1ccf98b0290c42529c6e03883faf07212021-12-02T05:36:34ZInvestigation on production of particleboard from Date palm residues1735-09132383-112X10.22092/ijwpr.1996.117436https://doaj.org/article/1ccf98b0290c42529c6e03883faf07211996-09-01T00:00:00Zhttp://ijwpr.areeo.ac.ir/article_117436_291e31b9227632f3750c2503a4666b52.pdfhttps://doaj.org/toc/1735-0913https://doaj.org/toc/2383-112XThe influence of production variable such as residues moisture content at time of chipping or flaking, hardner and press time on properties of particleboard from date palm residues is investigated. Each variable was investigated at three different levels and a total of 24 combinations of variables were studied. The results of this investigation indicate that: - Residues moisture content at the time of chipping or flaking affects both physical and mechanical properties of boards. MOR and MOE of board made from flakes produced by dry chipping and either wet or dry flaking was higher than others and its dimensional stability was better. Chipping or flaking moisture did not affect IB significantly. - Hardner consumption did not significantly influence the properties, but increasing hardner consumption to 3 percent of resin content (solid basis) improved board properties. - Press time also did not influence board properties and for the production of 15 mm. boards, either 5 or 6 minutes press time can be used. -For the production of boards to satisfy DIN requirement, following variable combination can be utilized: dry chipping - wet flaking, 3 percent hardner and 6 minutes press time.Ahmad Jahan latibariAbdolrahman HosseinzadehAmir NourbakhshAbolfazl KargarfardFardad GolbabaeiRegional Information Center for Science and Technology (RICeST)articleMORMOEDate palmForestrySD1-669.5FAتحقیقات علوم چوب و کاغذ ایران, Vol 1, Iss 1 شماره 148, Pp 50-110 (1996)
institution	DOAJ
collection	DOAJ
language	FA
topic	MOR MOE Date palm Forestry SD1-669.5
spellingShingle	MOR MOE Date palm Forestry SD1-669.5 Ahmad Jahan latibari Abdolrahman Hosseinzadeh Amir Nourbakhsh Abolfazl Kargarfard Fardad Golbabaei Investigation on production of particleboard from Date palm residues
description	The influence of production variable such as residues moisture content at time of chipping or flaking, hardner and press time on properties of particleboard from date palm residues is investigated. Each variable was investigated at three different levels and a total of 24 combinations of variables were studied. The results of this investigation indicate that: - Residues moisture content at the time of chipping or flaking affects both physical and mechanical properties of boards. MOR and MOE of board made from flakes produced by dry chipping and either wet or dry flaking was higher than others and its dimensional stability was better. Chipping or flaking moisture did not affect IB significantly. - Hardner consumption did not significantly influence the properties, but increasing hardner consumption to 3 percent of resin content (solid basis) improved board properties. - Press time also did not influence board properties and for the production of 15 mm. boards, either 5 or 6 minutes press time can be used. -For the production of boards to satisfy DIN requirement, following variable combination can be utilized: dry chipping - wet flaking, 3 percent hardner and 6 minutes press time.
format	article
author	Ahmad Jahan latibari Abdolrahman Hosseinzadeh Amir Nourbakhsh Abolfazl Kargarfard Fardad Golbabaei
author_facet	Ahmad Jahan latibari Abdolrahman Hosseinzadeh Amir Nourbakhsh Abolfazl Kargarfard Fardad Golbabaei
author_sort	Ahmad Jahan latibari
title	Investigation on production of particleboard from Date palm residues
title_short	Investigation on production of particleboard from Date palm residues
title_full	Investigation on production of particleboard from Date palm residues
title_fullStr	Investigation on production of particleboard from Date palm residues
title_full_unstemmed	Investigation on production of particleboard from Date palm residues
title_sort	investigation on production of particleboard from date palm residues
publisher	Regional Information Center for Science and Technology (RICeST)
publishDate	1996
url	https://doaj.org/article/1ccf98b0290c42529c6e03883faf0721
work_keys_str_mv	AT ahmadjahanlatibari investigationonproductionofparticleboardfromdatepalmresidues AT abdolrahmanhosseinzadeh investigationonproductionofparticleboardfromdatepalmresidues AT amirnourbakhsh investigationonproductionofparticleboardfromdatepalmresidues AT abolfazlkargarfard investigationonproductionofparticleboardfromdatepalmresidues AT fardadgolbabaei investigationonproductionofparticleboardfromdatepalmresidues
_version_	1718400280078319616

Investigation on production of particleboard from Date palm residues

Ejemplares similares