Correction: Development of a highly controlled system for large-area, directional printing of quasi-1D nanomaterials

Código QR

Correction: Development of a highly controlled system for large-area, directional printing of quasi-1D nanomaterials

Guardado en:

Detalles Bibliográficos
Autores principales:	Adamos Christou, Fengyuan Liu, Ravinder Dahiya
Formato:	article
Lenguaje:	EN
Publicado:	Nature Publishing Group 2021
Materias:	Technology T Engineering (General). Civil engineering (General) TA1-2040
Acceso en línea:	https://doaj.org/article/224bf59e68544079a902dec1a9ef50ca
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Direct roll transfer printed silicon nanoribbon arrays based high-performance flexible electronics
por: Ayoub Zumeit, et al.
Publicado: (2021)

Recent advances in the design of biosensors based on novel nanomaterials: An insight
por: Nidhi Chauhan, et al.
Publicado: (2021)

The crack quasi-static growth and analysis of interlaminar crack resistance of layered composite
por: Pavelko Igor, et al.
Publicado: (2021)

Research and Development of Food Industry’s Three-Dimensional Printing
por: Nezhmetdinov Ramil, et al.
Publicado: (2021)

A review on the fused deposition modeling (FDM) 3D printing: Filament processing, materials, and printing parameters
por: Kristiawan Ruben Bayu, et al.
Publicado: (2021)

Development of Solar-Powered Water Pump with 3D Printed Impeller
por: Andres Nelson S.
Publicado: (2021)

Special Issue: The Science and Technology of 3D Printing
por: Tuhin Mukherjee
Publicado: (2021)

An interpretation of Temam’s extra force in the quasi-incompressible Navier–Stokes system
por: Giuseppe Tomassetti
Publicado: (2021)

Modeling a Large Air-Cooled Condenser
por: Louw D.L., et al.
Publicado: (2021)

Correction
Publicado: (2019)

Correction
Publicado: (2019)

A New Fractal Printed Dipole Antenna Based on Tent Transformations for Wireless Communication Applications
por: Jawad K. Ali
Publicado: (2019)

Desalination of Highly Saline Water Using Direct Contact Membrane Distillation (DCMD)
por: Salah S. Ibrahim, et al.
Publicado: (2019)

Comparisons of Mechanical Properties of sub-mm Lead Based and Lead Free Based Solder Using in Manufacturing of Printed Circuits
por: Alaa Hasan Ali
Publicado: (2014)

Influence of Recrystallization Annealing Modes on the Mechanical Properties of Copper Pipes After Large Plastic Deformation
por: Shalaeva Maria, et al.
Publicado: (2021)

Estimations of the Jacking Forces of Large-Sized Rectangular Jacking Pipes Based on a Displacement Control Method
por: Zun-Qun Xiao, et al.
Publicado: (2021)

Implementation of a Group Cutting Scheme during Processing of Large-Module Gears with a Prefabricated Tool
por: Artamonov E.V., et al.
Publicado: (2021)

Analytical first derivatives of the direct Hermite-Simpson collocation formulation of optimal control problems
por: Arunakirinathar Aravind, et al.
Publicado: (2021)

A quasi-coupled wind wave experimental framework for testing offshore wind turbine floating systems
por: C. Feist, et al.
Publicado: (2021)

Field Study on Deformation and Stress Characteristics of Large Open Caisson during Excavation in Deep Marine Soft Clay
por: Xin Yan, et al.
Publicado: (2021)

Mechanical property evaluation of apricot fruits under quasi-static and dynamic loading
por: E Ahmadi, et al.
Publicado: (2016)

Publisher Correction to: Journal of Engineering and Applied Science, vol 68
por: Journal of Engineering and Applied Science
Publicado: (2021)

Thermal Deformations of Thermoplast during 3D Printing: Warping in the Case of ABS
por: Jakub Ramian, et al.
Publicado: (2021)

Control of Omni-Directional Mobile Robot Motion
por: A. Salam Al-Ammri, et al.
Publicado: (2010)

Dynamics of unsteady reactive flow of viscous nanomaterial subject to Ohmic heating, heat source and viscous dissipation
por: Wei-Feng Xia, et al.
Publicado: (2021)

Large Angle Bending Behavior of Curved Members UsingThe Method of Characteristics
por: Essam Z. Fadhel, et al.
Publicado: (2008)

Large Angle Bending Behavior of Curved Members Using The Method of Characteristics
por: Haitham H. Al-Da'ami, et al.
Publicado: (2019)

Interlayer Strength of 3D-Printed Mortar Reinforced by Postinstalled Reinforcement
por: Jihun Park, et al.
Publicado: (2021)

Biocompatible Dispersants for Carbon Nanomaterials
por: Hugh Mohan, et al.
Publicado: (2021)

Propagating acoustic waves on a culture substrate regulate the directional collective cell migration
por: Chikahiro Imashiro, et al.
Publicado: (2021)

Hybrid Materials Based on Fly Ash, Metakaolin, and Cement for 3D Printing
por: Joanna Marczyk, et al.
Publicado: (2021)

Birnbaum-Saunders Durability Life Prediction Model of Site-Exposed Concrete in the Saline Soil Area
por: Chenggong Lu, et al.
Publicado: (2021)

New Insights into the Application of 3D-Printing Technology in Hernia Repair
por: Bárbara Pérez-Köhler, et al.
Publicado: (2021)

GROUNDWATER FLOW MODELING FOR MANAGEMENT AND DEVELOPMENT SYSTEMS IN THE URBAN AREA OF MAJENE DISTRICT, WEST SULAWESI PROVINCE
por: Aji Marwadi
Publicado: (2021)

Multi-criteria Optimization in Solving the Problem of Expanding Production Capacity of an Enterprise as a Method of Modeling Strategic Directions for the Development of Production Systems
por: Shatalova Olga, et al.
Publicado: (2021)

Recent Advances in the Surface Functionalization of Nanomaterials for Antimicrobial Applications
por: Shahin Shah Khan, et al.
Publicado: (2021)

Overview of the Development of 3D-Printing Concrete: A Review
por: Fuyan Lyu, et al.
Publicado: (2021)

Gyrotactic microorganism and bio-convection during flow of Prandtl-Eyring nanomaterial
por: Hayat Tasawar, et al.
Publicado: (2021)

Recent Advancements in the Nanomaterial Application in Concrete and Its Ecological Impact
por: Haleema Saleem, et al.
Publicado: (2021)

Design and Simulation of a Titanium Alloy Lattice Bone Plate for 3D Printing
por: ZHANG Cong, et al.
Publicado: (2021)