Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System
The main emphasis of research for battery wireless charger should be on four parts, including load-independent output to satisfy the charging requirement, zero voltage switching of power devices to increase transmission efficiency, minimum component counts to reduce cost and simple control strategy....
Guardado en:
Autores principales: | , |
---|---|
Formato: | article |
Lenguaje: | EN |
Publicado: |
IEEE
2021
|
Materias: | |
Acceso en línea: | https://doaj.org/article/42eedaa984da456289f641361052cc34 |
Etiquetas: |
Agregar Etiqueta
Sin Etiquetas, Sea el primero en etiquetar este registro!
|
id |
oai:doaj.org-article:42eedaa984da456289f641361052cc34 |
---|---|
record_format |
dspace |
spelling |
oai:doaj.org-article:42eedaa984da456289f641361052cc342021-11-18T00:08:13ZFrequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System2169-353610.1109/ACCESS.2021.3123471https://doaj.org/article/42eedaa984da456289f641361052cc342021-01-01T00:00:00Zhttps://ieeexplore.ieee.org/document/9590547/https://doaj.org/toc/2169-3536The main emphasis of research for battery wireless charger should be on four parts, including load-independent output to satisfy the charging requirement, zero voltage switching of power devices to increase transmission efficiency, minimum component counts to reduce cost and simple control strategy. However, the existing studies have not taken these all into account, which greatly limits the application of battery wireless charger. This paper proposes a WPT system based on the simplest S/S compensation network. By replacing the secondary compensation capacitor with an <inline-formula> <tex-math notation="LaTeX">$L$ </tex-math></inline-formula>-<inline-formula> <tex-math notation="LaTeX">$C$ </tex-math></inline-formula> branch, the same circuit structure can realize the load-independent constant current (CC) and voltage (CV) output with zero voltage switching at two different switching frequency. A current amplitude detection circuit is added in the primary side to determine the switching point of CC mode and CV mode. Compared with existing research, the component numbers in proposed circuit are less, the control strategy is easier to implement and avoids the communication between the primary and secondary sides. Finally, a wireless battery charger for 60V/3.6A is built to verify the feasibility of proposed system. And the experimental results perform well on realizing a load-independent output with ZVS operation.Bing ChengLiangzong HeIEEEarticleWireless power transfer (WPT)adaptive branchload estimationload-independent outputzero voltage switching (ZVS)Electrical engineering. Electronics. Nuclear engineeringTK1-9971ENIEEE Access, Vol 9, Pp 148884-148893 (2021) |
institution |
DOAJ |
collection |
DOAJ |
language |
EN |
topic |
Wireless power transfer (WPT) adaptive branch load estimation load-independent output zero voltage switching (ZVS) Electrical engineering. Electronics. Nuclear engineering TK1-9971 |
spellingShingle |
Wireless power transfer (WPT) adaptive branch load estimation load-independent output zero voltage switching (ZVS) Electrical engineering. Electronics. Nuclear engineering TK1-9971 Bing Cheng Liangzong He Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
description |
The main emphasis of research for battery wireless charger should be on four parts, including load-independent output to satisfy the charging requirement, zero voltage switching of power devices to increase transmission efficiency, minimum component counts to reduce cost and simple control strategy. However, the existing studies have not taken these all into account, which greatly limits the application of battery wireless charger. This paper proposes a WPT system based on the simplest S/S compensation network. By replacing the secondary compensation capacitor with an <inline-formula> <tex-math notation="LaTeX">$L$ </tex-math></inline-formula>-<inline-formula> <tex-math notation="LaTeX">$C$ </tex-math></inline-formula> branch, the same circuit structure can realize the load-independent constant current (CC) and voltage (CV) output with zero voltage switching at two different switching frequency. A current amplitude detection circuit is added in the primary side to determine the switching point of CC mode and CV mode. Compared with existing research, the component numbers in proposed circuit are less, the control strategy is easier to implement and avoids the communication between the primary and secondary sides. Finally, a wireless battery charger for 60V/3.6A is built to verify the feasibility of proposed system. And the experimental results perform well on realizing a load-independent output with ZVS operation. |
format |
article |
author |
Bing Cheng Liangzong He |
author_facet |
Bing Cheng Liangzong He |
author_sort |
Bing Cheng |
title |
Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
title_short |
Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
title_full |
Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
title_fullStr |
Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
title_full_unstemmed |
Frequency Adaptive Topology to Realize Constant Output and Soft Switching for the WPT System |
title_sort |
frequency adaptive topology to realize constant output and soft switching for the wpt system |
publisher |
IEEE |
publishDate |
2021 |
url |
https://doaj.org/article/42eedaa984da456289f641361052cc34 |
work_keys_str_mv |
AT bingcheng frequencyadaptivetopologytorealizeconstantoutputandsoftswitchingforthewptsystem AT liangzonghe frequencyadaptivetopologytorealizeconstantoutputandsoftswitchingforthewptsystem |
_version_ |
1718425221415829504 |