Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion
In the present work, the behavior of thick-walled cylinder of elasto-plastic material (polymeric material) has been studied analytically. The study is based on modified Von-Mises yield criterion (for non metallic material). The equations of stress distribution are obtained for the cylinder under ge...
Guardado en:
Autores principales: | , , |
---|---|
Formato: | article |
Lenguaje: | EN |
Publicado: |
Al-Khwarizmi College of Engineering – University of Baghdad
2019
|
Materias: | |
Acceso en línea: | https://doaj.org/article/6f50b1a496a54056acef4b4849639cec |
Etiquetas: |
Agregar Etiqueta
Sin Etiquetas, Sea el primero en etiquetar este registro!
|
id |
oai:doaj.org-article:6f50b1a496a54056acef4b4849639cec |
---|---|
record_format |
dspace |
spelling |
oai:doaj.org-article:6f50b1a496a54056acef4b4849639cec2021-12-02T04:29:59ZThermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion1818-11712312-0789https://doaj.org/article/6f50b1a496a54056acef4b4849639cec2019-03-01T00:00:00Zhttp://alkej.uobaghdad.edu.iq/index.php/alkej/article/view/610https://doaj.org/toc/1818-1171https://doaj.org/toc/2312-0789 In the present work, the behavior of thick-walled cylinder of elasto-plastic material (polymeric material) has been studied analytically. The study is based on modified Von-Mises yield criterion (for non metallic material). The equations of stress distribution are obtained for the cylinder under general cases of elastic expansion, plastic initiation and elastic-plastic expansion. A computer program is developed for evaluating the stress distribution. The solution is carried out for worst boundary conditions when the cylinder is subjected to the combination of pressure load, inertia load, and temperature gradient. The results are presented graphically in terms of dimensionless stresses and radius ratio. They indicate that the thermal and rotational loads are greatly influencing the stress distribution and the initiation of plastic zone, as well as the spreading out of the plastic zone. Moreover, it was found that the critical values of loads required for starting plastic deformation are determined by the amount of the applied load and the type of loading conditions, and it is found that the variation of stresses are greatly influenced by increasing of the temperature gradient at constant pressure and inertial loads than other increases in loading conditions. Imad A. HussainHameed D. LaftaRafa'a D. HussainAl-Khwarizmi College of Engineering – University of BaghdadarticleChemical engineeringTP155-156Engineering (General). Civil engineering (General)TA1-2040ENAl-Khawarizmi Engineering Journal, Vol 4, Iss 4 (2019) |
institution |
DOAJ |
collection |
DOAJ |
language |
EN |
topic |
Chemical engineering TP155-156 Engineering (General). Civil engineering (General) TA1-2040 |
spellingShingle |
Chemical engineering TP155-156 Engineering (General). Civil engineering (General) TA1-2040 Imad A. Hussain Hameed D. Lafta Rafa'a D. Hussain Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
description |
In the present work, the behavior of thick-walled cylinder of elasto-plastic material (polymeric material) has been studied analytically. The study is based on modified Von-Mises yield criterion (for non metallic material). The equations of stress distribution are obtained for the cylinder under general cases of elastic expansion, plastic initiation and elastic-plastic expansion.
A computer program is developed for evaluating the stress distribution. The solution is carried out for worst boundary conditions when the cylinder is subjected to the combination of pressure load, inertia load, and temperature gradient.
The results are presented graphically in terms of dimensionless stresses and radius ratio. They indicate that the thermal and rotational loads are greatly influencing the stress distribution and the initiation of plastic zone, as well as the spreading out of the plastic zone. Moreover, it was found that the critical values of loads required for starting plastic deformation are determined by the amount of the applied load and the type of loading conditions, and it is found that the variation of stresses are greatly influenced by increasing of the temperature gradient at constant pressure and inertial loads than other increases in loading conditions.
|
format |
article |
author |
Imad A. Hussain Hameed D. Lafta Rafa'a D. Hussain |
author_facet |
Imad A. Hussain Hameed D. Lafta Rafa'a D. Hussain |
author_sort |
Imad A. Hussain |
title |
Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
title_short |
Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
title_full |
Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
title_fullStr |
Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
title_full_unstemmed |
Thermo Elasto-Plastic Analysis of Rotating Axisymmetrical Bodies Using Modified Von-Mises Yield Criterion |
title_sort |
thermo elasto-plastic analysis of rotating axisymmetrical bodies using modified von-mises yield criterion |
publisher |
Al-Khwarizmi College of Engineering – University of Baghdad |
publishDate |
2019 |
url |
https://doaj.org/article/6f50b1a496a54056acef4b4849639cec |
work_keys_str_mv |
AT imadahussain thermoelastoplasticanalysisofrotatingaxisymmetricalbodiesusingmodifiedvonmisesyieldcriterion AT hameeddlafta thermoelastoplasticanalysisofrotatingaxisymmetricalbodiesusingmodifiedvonmisesyieldcriterion AT rafaadhussain thermoelastoplasticanalysisofrotatingaxisymmetricalbodiesusingmodifiedvonmisesyieldcriterion |
_version_ |
1718401191347486720 |