Cutting corners: donning under duress–a VR teaching tool

Código QR

Cutting corners: donning under duress–a VR teaching tool

Guardado en:

Detalles Bibliográficos
Autores principales:	Shikha Bansal, Julian Wiegelmann, Clyde Matava, Catherine Bereznicki, Fahad Alam
Formato:	article
Lenguaje:	EN
Publicado:	Canadian Medical Education Journal 2021
Materias:	Education (General) L7-991 Medicine (General) R5-920
Acceso en línea:	https://doaj.org/article/95bfc0fc10cb47cd8ce5bbb0e4b9a805
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Journalism under duress in Asia-Pacific: A decade of resistance
por: David Robie
Publicado: (2018)

Cutting tool standardization
por: Ostapenko Maria, et al.
Publicado: (2021)

A Method for Calculating the Velocity of Corner-to-Corner Rear-End Collisions of Vehicles Based on Collision Deformation Analysis
por: Yi Cao, et al.
Publicado: (2021)

study on the cut load test, siding strength of two ready-to-assemble corner joints and comparing them with fixed joints
por: Mohammad Ghofrani, et al.
Publicado: (2012)

The More, the Better? Improving VR Firefighting Training System with Realistic Firefighter Tools as Controllers
por: Seunggon Jeon, et al.
Publicado: (2021)

AUTOMATED CUTTING TOOLS SELECTION FOR BEARINGS COMPONENTS TURNING PROCESS
por: DAN GEORGE PRUTICA, et al.
Publicado: (2020)

To the Question of the Reasons for Decrease in the Durability of Cutting Tools with a Diamond-Like Coating
por: Lieberman Yacov, et al.
Publicado: (2021)

Embedded VR Video Image Control System in the Ideological and Political Teaching System Based on Artificial Intelligence
por: Fengzhen Jia, et al.
Publicado: (2021)

Application of Virtual Reality (VR) Technologies in Management and Education
por: A. I. Sosnilo
Publicado: (2021)

Dependence of Elastic Deformations of Spindle-Tool Subsystem on Influence of Cutting Force Radial Component
por: Kazakova O. Yu., et al.
Publicado: (2021)

Seeing around corners with edge-resolved transient imaging
por: Joshua Rapp, et al.
Publicado: (2020)

Minimizing the cost of a curved corner trapezoidal canal section
por: Ehab M. Fattouh, et al.
Publicado: (2021)

Implementation of a Group Cutting Scheme during Processing of Large-Module Gears with a Prefabricated Tool
por: Artamonov E.V., et al.
Publicado: (2021)

Development of Immersive VR Device for Gait Training Rehabilitation with Biofeedback System-Preliminary Study
por: Jeong-Woo Seo, et al.
Publicado: (2021)

Online Tools for Teaching Cancer Bioinformatics
por: Mason D. Taylor, et al.
Publicado: (2021)

Real-Time Local Optimal Bézier Corner Smoothing for CNC Machine Tools
por: Tzyy-Chyang Lu, et al.
Publicado: (2021)

Chemotaxis on the Move – Active Learning Teaching Tool
por: Ann H. Williams
Publicado: (2010)

Suitability of natural rocks as materials for cutting tools
por: Berend Denkena, et al.
Publicado: (2021)

The Role of Clinical Hypnosis & VR in Special Education
por: Athanasios Drigas, et al.
Publicado: (2021)

VR & AR TECHNOLOGIES: OPPORTUNITIES AND APPLICATION OBSTACLES
por: A. V. Ivanova
Publicado: (2018)

Study and Comparison of Lubricity of Green and Commercial Cutting Fluid Using Tool-Chip Tribometer
por: Suvin Parayantayyathu Somarajan, et al.
Publicado: (2018)

Usefulness of upright T wave in lead aVR for predicting short-term prognosis of patients with ischemic stroke
por: Hong-Jie Yang, et al.
Publicado: (2018)

Development of novel tool for cutting of carbon-fiber-reinforced plastics (Positive use of abrasive wear at tool edge for reduction in cutting force)
por: Satoru MAEGAWA, et al.
Publicado: (2015)

Hospitalization in older patients due to adverse drug reactions – the need for a prediction tool
por: Parameswaran Nair N, et al.
Publicado: (2016)

Application of Multi-Contour Cutting in Algorithms for Solving the Cutting Path Problem
por: Tavaeva Anastasiia, et al.
Publicado: (2021)

The bulk-corner correspondence of time-reversal symmetric insulators
por: Sander Kooi, et al.
Publicado: (2021)

Passive sensing around the corner using spatial coherence
por: M. Batarseh, et al.
Publicado: (2018)

Multipolar lasing modes from topological corner states
por: Ha-Reem Kim, et al.
Publicado: (2020)

The fracture moment of corner joints bonded by different glues
por: Jasna Hrovatin, et al.
Publicado: (2014)

Quality of Corner Joints of Beech Chairs under Load
por: Silvana Prekrat, et al.
Publicado: (2012)

Scientific Methods for Determination of Wooden Corner Joint Designs
por: Španić Nikola, et al.
Publicado: (2009)

Confluence: A Seminar Series as a Teaching Tool
por: Bryan M. Dewsbury, et al.
Publicado: (2013)

Effect Ti/AlTiN Multilayer Coating on the Crater Wear Process of Cutting Tool and Tribological Properties
por: Kamil J. Kadhim, et al.
Publicado: (2018)

Suppression of tool wear by extremely short-duration cutting
por: Yuki TERASAKA, et al.
Publicado: (2015)

Tool-Workpiece Interaction in the Cutting Process and Its Use
por: Karol Vasilko, et al.
Publicado: (2021)

2019nCoVR—A comprehensive genomic resource for SARS-CoV-2 variant surveillance
por: Guoqing Lu, et al.
Publicado: (2021)

Don Gildo D'Accurzio
por: Pro, Diego F.
Publicado: (1989)

Turning Tool Wear Estimation Based on the Calculated Parameter Values of the Thermodynamic Subsystem of the Cutting System
por: Victor Petrovich Lapshin
Publicado: (2021)

Moss in the Classroom: A Tiny but Mighty Tool for Teaching Biology
por: Erin E. Shortlidge, et al.
Publicado: (2015)

Corner states in a second-order mechanical topological insulator
por: Chun-Wei Chen, et al.
Publicado: (2021)