Microstructure and tribological properties of Co-Ti<sub>3</sub>SiC<sub>2</sub> self-lubricating composite coatings on 304 stainless steel by laser cladding

The self lubricating wear-resistant coatings were prepared on the surface of 304 stainless steel successfully using laser cladding synchronous powder feeding method, the ratio of cladding powder was pure Co, Co-2%Ti<sub>3</sub>SiC<sub>2</sub>(mass fraction, the same below) an...

Descripción completa

Guardado en:
Detalles Bibliográficos
Autores principales: WANG Gang, LIU Xiu-bo, LIU Yi-fan, ZHU Yang, OUYANG Chun-sheng, MENG Yuan, LUO Ying-she
Formato: article
Lenguaje:ZH
Publicado: Journal of Materials Engineering 2021
Materias:
Acceso en línea:https://doaj.org/article/9a294a8485804aa5801697ed7e6fd49f
Etiquetas: Agregar Etiqueta
Sin Etiquetas, Sea el primero en etiquetar este registro!
Descripción
Sumario:The self lubricating wear-resistant coatings were prepared on the surface of 304 stainless steel successfully using laser cladding synchronous powder feeding method, the ratio of cladding powder was pure Co, Co-2%Ti<sub>3</sub>SiC<sub>2</sub>(mass fraction, the same below) and Co-8%Ti<sub>3</sub>SiC<sub>2</sub>. The microstructure of the cladding coating was characterized by scanning electron microscope(SEM), energy spectrum analyzer(EDS) and X-ray diffractometer(XRD). The tribological performance and related mechanisms of 304 substrate and coatings at RT/600℃ were systematically investigated. The results show that the average microhardness of the N1, N2 and N3 coatings are 285.7HV<sub>0.5</sub>, 356.3HV<sub>0.5</sub> and 463.8HV<sub>0.5</sub>, which are all much higher than that of the matrix(240.3HV<sub>0.5</sub>). Co-Ti<sub>3</sub>SiC<sub>2</sub> composite coatings are composed of continuous matrix γ-Co solid solution, hard phase (Fe<sub>2</sub>C, Cr<sub>7</sub>C<sub>3</sub> and TiC) and lubricating phase Ti<sub>3</sub>SiC<sub>2</sub>. At room temperature, the friction coefficients of the matrix and the N1, N2 and N3 coatings are 0.56, 0.62, 0.68 and 0.42, the wear rates of the N1, N2, N3 coatings are 9.15×10<sup>-5</sup>, 7.81×10<sup>-5</sup>, 4.66×10<sup>-5</sup> mm<sup>3</sup>/(N·m), which are lower than that of the matrix (66.42×10<sup>-5</sup> mm<sup>3</sup>/(N·m)); at high temperature, the friction coefficients of the matrix and the N1, N2 and N3 coatings are 0.66, 0.54, 0.52 and 0.46, the wear rates of the N1, N2, N3 coatings are 37.79×10<sup>-5</sup>, 35.6×10<sup>-5</sup>, 18.83×10<sup>-5</sup> mm<sup>3</sup>/(N·m), which are lower than that of the matrix (41.3×10<sup>-5</sup> mm<sup>3</sup>/(N·m)).At room temperature and 600℃, compared with the 304 stainless substrate, the coatings have the obvious higher microhardness, and the Co-8%Ti<sub>3</sub>SiC<sub>2</sub> coating exhibits the best self-lubricating wear resistance.