Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process

This article is devoted to the economic and technical aspects of the research on continuous noncontact measurement of the workpiece diameter during the manufacturing operation using a suitably selected and designed sensor. In order to achieve this main goal, it was necessary to meet these partial go...

Descripción completa

Guardado en:

Detalles Bibliográficos
Autores principales:	Radoslav Kreheľ, Patrik Szentivanyi, Marek Kočiško, Martin Pollák
Formato:	article
Lenguaje:	EN
Publicado:	Hindawi Limited 2021
Materias:	Materials of engineering and construction. Mechanics of materials TA401-492
Acceso en línea:	https://doaj.org/article/b56cb781ede442d6b52ae4db99db0131
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

id	oai:doaj.org-article:b56cb781ede442d6b52ae4db99db0131
record_format	dspace
spelling	oai:doaj.org-article:b56cb781ede442d6b52ae4db99db01312021-11-29T00:56:31ZTechnical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process1687-844210.1155/2021/3373197https://doaj.org/article/b56cb781ede442d6b52ae4db99db01312021-01-01T00:00:00Zhttp://dx.doi.org/10.1155/2021/3373197https://doaj.org/toc/1687-8442This article is devoted to the economic and technical aspects of the research on continuous noncontact measurement of the workpiece diameter during the manufacturing operation using a suitably selected and designed sensor. In order to achieve this main goal, it was necessary to meet these partial goals. We develop and describe a method of accurate continuous technical measurement of the workpiece diameter during the machining process. We propose a principle of continuous technical measurement of workpiece diameter, design a scanning method based on this principle, and verify the developed equipment on a specific case of technical measurement. At the same time, the development includes the expansion of the use for continuous noncontact measurement of workpiece vibrations. Based on test measurements, an optical sensor was selected, the analysis of which is presented in a part of the article. The introduction of this article provides a simple view of the need for continuous measurement of the workpiece diameter. The second chapter presents the current state of the problem. The third chapter is devoted to the theoretical analysis and description of practical implementations of the solution. The conclusion, as it could be expected, includes evaluation of the results.Radoslav KreheľPatrik SzentivanyiMarek KočiškoMartin PollákHindawi LimitedarticleMaterials of engineering and construction. Mechanics of materialsTA401-492ENAdvances in Materials Science and Engineering, Vol 2021 (2021)
institution	DOAJ
collection	DOAJ
language	EN
topic	Materials of engineering and construction. Mechanics of materials TA401-492
spellingShingle	Materials of engineering and construction. Mechanics of materials TA401-492 Radoslav Kreheľ Patrik Szentivanyi Marek Kočiško Martin Pollák Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
description	This article is devoted to the economic and technical aspects of the research on continuous noncontact measurement of the workpiece diameter during the manufacturing operation using a suitably selected and designed sensor. In order to achieve this main goal, it was necessary to meet these partial goals. We develop and describe a method of accurate continuous technical measurement of the workpiece diameter during the machining process. We propose a principle of continuous technical measurement of workpiece diameter, design a scanning method based on this principle, and verify the developed equipment on a specific case of technical measurement. At the same time, the development includes the expansion of the use for continuous noncontact measurement of workpiece vibrations. Based on test measurements, an optical sensor was selected, the analysis of which is presented in a part of the article. The introduction of this article provides a simple view of the need for continuous measurement of the workpiece diameter. The second chapter presents the current state of the problem. The third chapter is devoted to the theoretical analysis and description of practical implementations of the solution. The conclusion, as it could be expected, includes evaluation of the results.
format	article
author	Radoslav Kreheľ Patrik Szentivanyi Marek Kočiško Martin Pollák
author_facet	Radoslav Kreheľ Patrik Szentivanyi Marek Kočiško Martin Pollák
author_sort	Radoslav Kreheľ
title	Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
title_short	Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
title_full	Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
title_fullStr	Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
title_full_unstemmed	Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process
title_sort	technical and economic description of the research on a measuring device for continuous measurement of the diameter and vibration of the workpiece during the machining process
publisher	Hindawi Limited
publishDate	2021
url	https://doaj.org/article/b56cb781ede442d6b52ae4db99db0131
work_keys_str_mv	AT radoslavkrehel technicalandeconomicdescriptionoftheresearchonameasuringdeviceforcontinuousmeasurementofthediameterandvibrationoftheworkpieceduringthemachiningprocess AT patrikszentivanyi technicalandeconomicdescriptionoftheresearchonameasuringdeviceforcontinuousmeasurementofthediameterandvibrationoftheworkpieceduringthemachiningprocess AT marekkocisko technicalandeconomicdescriptionoftheresearchonameasuringdeviceforcontinuousmeasurementofthediameterandvibrationoftheworkpieceduringthemachiningprocess AT martinpollak technicalandeconomicdescriptionoftheresearchonameasuringdeviceforcontinuousmeasurementofthediameterandvibrationoftheworkpieceduringthemachiningprocess
_version_	1718407729624645632

Technical and Economic Description of the Research on a Measuring Device for Continuous Measurement of the Diameter and Vibration of the Workpiece during the Machining Process

Ejemplares similares